With the change of draw bar pins, or pin bushings, our 3 Point Mount, accepts category 1, 2 & 3 narrow.
3 point hydraulic wire winder, shown set up for category 2, with optional, hand control wire guide.
Hydraulic 3 Point Winder
If you have both the Cat-1 (7/8") and Cat-2 (1-1/8") pins, or pin bushings to slide over the cat 1 pins to make it cat 2, it is very easy to convert the new Pro-Tatch Winder frame from Cat-1 to Cat-2 mount and back again.
Manual Wire Guide Arm (as shown in photos above) is an accessory that can
be added to any new or used 3 point wire winder.
Hydraulic 3 Point Winder
Hydraulic Wire Winder ww-174 $949.00 ( ships ups )
Optional Guide Arm $129.00 ( ships ups )
|Select Winder Category|
Over 19,000 in use world wide!
The strongest 3pt. wire winders on the market today!
The ball valve is your variable speed / safety control. It should be used more as a safety shut off, than a speed control. It is best to control the speed from the hydraulics on the tractor.
Our wire winder's hydraulic motor, provides ample power for hard jobs, like pulling
barbed wire through tall grass. This motor will create roughly 12 horse power, that will easily pull old wire up out of the grass and trash that collects in a fence line over the years.
Standard Features and operation:
- Always regulate speed of this unit from the hydraulics on tractor.
- Always plug valve hose into power side of hydraulics.
- Designed for smooth or barbed wire or light cable.
- designed to pull wire in to unit ( always have a weight on the end of the wire. ) A short piece of log chain or the best is, the window weights out of old houses.
- Winder frame converts for Category 1, Category 2 & Category 3 narrow 3 point mounts (special orders upon request).
- Removable yellow split reel. Hand spun smooth steel, designed with safety in mind.
- Holds 1/2 mile of barbed or 1 mile of smooth wire.
- Replaceable moly-impregnated polyethylene bushings on shaft to prevent wear. This bushing has proven to last for years of performance in the field.
- Hydraulic motor creates 12 horse power under full load.
- 1/2" male pipe ends on hydraulic hose's ( we do not include hose tips )
- Always, start slow and stop slow, to prevent damage to lovejoy coupler between motor and drive shaft. With the inertia of the spinning reel, a fast stop can cause damage to the coupler. This is not common, but can happen if the wire winder is not operated correctly.
Don't forget to ask about our wire guide, which can be added to your 3 point wire winder ($129.00).
The Wire Guide can be added to any new or existing Pro-Tatch wire winder, no matter its age.
This option has become very popular with anyone using our hydraulic wire winders.
The wire guide can be used on all units including the Magnum, shown above, with the dual cone reels.
The yellow vertical bars out in front of the reel on the guide, are roller sleeves that will keep any type of wire rolling between the guide arms. These are a must when rolling barbed wire.
Manufactured of steel with a comfort grip handle, baked on powder coat finish, this unit is designed to last for the life of your winder.
Winder Guide Arm
WG123 (FOR CATEGORY 1-2-3 hydraulic): $129.00 (EACH) + shipping
UNWG (FOR UNIVERSAL hydraulic): $129.00 (EACH) + shipping
MAWG (FOR MAGNUM hydraulic): $129.00 (EACH) + shipping
BBWG (FOR BALE BED hydraulic): $129.00 (EACH)+ shipping
The strongest 3pt. wire winders on the market today. Over 19,000 in use world wide. Watch the video above, to see the smooth action and the ease of operation.
This new design we came out with a few years ago on the mount was done to make it easier to work on all the new quick hitch 3 points out there today. This winder works exactly like the unit we previously manufactured, as far back as 1986, it is only the mounting we changed.
Photo above shows the 7/8" 3 point pins in the category 1 position. This is done by turning them inwards, as you can see in the photo.
Top link has both cat 1 and cat 2, along with cat 3 narrow, holes in place. Unit shown with optional wire guide.
Photo above shows the 1 1/8" 3 point pins in the category 2 position. This is done by mounting them facing outwards, as you can see in the photo.
Top link has both cat 1 and cat 2, along with cat 3 narrow, holes in place. Shown with optional wire guide.
Designed to be used on high tensile, its 8” center you will not roll the high tensile wire as tight, in a small coil when rolling. Capacity is 1 mile of wire. The outside diameter of this reel is 20".
The 4” center standard reel measures 20” in diameter with a 4" center, and is designed to be used on any type of wire. It will comfortably hold 1 mile of smooth or 1/2 mile of barbed wire.
The 4” mini solid reel is 12” in diameter with a 4" center, designed to hold smooth or barbed wire. It will comfortably hold 1/2 mile smooth wire.
All 3 designs are manufactured of steel with baked on powder coat finish.
All 3 solid reels shown are UPS shippable.
This 4" mini spool, is designed to be used on all Pro-Tatch wire winders just like our other solid reels.
It will comfortably hold 1/2 mile smooth wire. It can also be used to roll barbed wire as well.
Very easy to handle and store. All steel construction to last for years of use.
SOLID REEL PART NUMBERS & DIMENSIONS
NS-1752 (4"MINI): 12" outside diameter with 4" center
NS-1754 (4" CENTER): 20" outside diameter with 4" center
NS-1758 (8" CENTER): 20" outside diameter with 4" center
Solid Reels pricing
NS-1752 (4"MINI): $55.00 + SHIPPPING
NS-1754 (4" CENTER): $77.00 + SHIPPING
NS-1758 (8" CENTER): $82.00 + SHIPPING
All of our winders (excluding the GAS POWERED and HIGH TENSILE) ship for free.
Gas powered and high tensile units ship palletized, truck freight. ( All other units are UPS shippable)
We do not ship wire winder ACCESSORIES for free. Please contact us to determine shipping charges on any accessories that may include such items as solid reels, wire guides or any extra parts and accessories you may want to order, call 1-877-407-8645.
Optional UNROLLING Arm
Optional arm designed for unrolling new rolls of wire. Designed to mount to any 3 point hydraulic wire winder, manufactured by Pro-Tatch Inc.
We have adapted this same unit to ATV's, Pickups, etc. ( the customer can adapt it to what ever fits his needs)
UNROLLing Arm - $179.00 + SHIPPING
Its been 30 plus years since we built the very first wire winder, here at Hotwood's and we would like to sincerely thank all the wonderful farmers and ranchers across the world that have made this wire winder dream a reality.
We cannot show you all of them, but this is a few that have stopped by over the years in our Grand Island, Nebraska location to pick up their wire wire.
Hotwood's, keeping America rolling with jobs, and shipping world wide for 30 plus years.