Shipping charges apply on our Gas Powered Winder's

HOTwoODs Gas Powered wire Winder

This unit offers the manual level wind. Comes complete with safety shields as shown and can be set in the back of the pickup or flatbed as well as run on the ground. Tie off steel ring loops welded on each end to secure it as you are rolling wire.

Pro-Tatch inc. Honda Gas Powered Winder

 Comes with reliable 5.5 hp. Honda pull start gas engine. Motor carries a 3 year warranty, through Honda. We will not manufacture our products, with anything less than the best, that is why we use Honda.
The handle on the manual wire guide, can be moved from right to left, depending on what side you are working the machine from.

Clutch can be operated from either side.

Removable shield's on both the belt drive and the chain drive. ( easy to service )

Standard with manual wire guide.

Tie off hooks to secure it to your truck or trailer when rolling wire.

Lift hook, located centrally on the machine to use if needed to load.

Split reel is designed to be used over and over.

Reel is designed with 4 tie wire points to place tie wires in before starting to roll wire.

Yellow split reel is the same reel we use on all our winders. However, the high tensile reel will not fit on this unit. If you are rolling high tensile with this unit, we recommend the 8" center solid reel.

After you service your new gas powered winder, and it is ready to use the first time, you may need to adjust the motor on the motor mount base to the right tension on the belt, as it takes a while to season the belt and get the best performance from your new winder.

When you receive your gas winder, it will be assembled on a pallet and will only need to have the engine serviced, with oil before it is ready to run.

Use 10-30 motor oil ( service on a regular basis, depending on use )

Ships dry only. ( no oil in engine ) we cannot ship, with oil in the crankcase.

Ships truck freight only. ( unit weighs 165 lbs.)

Call toll free 877-407-8645 for a freight quote and order your new winder today. 

Unit shown in pickup, can be used in a side by side UTV or any other type of vehicle or piece of equipment, you may use while doing your fencing. 

This is going to be the location you will want your Gas Powered Wire Winder when operating it off the tail gate of any pickup. 

NOTE: Always have your winder secured to the pickup with the 2 tie off loops located on the front crossmember of the wire winder frame. This can be done by straps or chain connected to the interior hooks of your pickup box. This will prevent the unit from pulling itself off the back of the pickup while rolling wire.

Honda motor ships dry. ( No oil in crankcase ) 

You may need to adjust the motor when you first get it, with the 4 slide bolts under the motor on the frame, to make sure the motor and drive belt have the right tension to operate correctly.

It may take a while to get it set perfectly, as they call it, seasoning the belt. This is when the belt has ran a few hours and is seasoned, or formed to the pulleys and the pulleys are smoothed up from it running on them. 

gas_wire_winder.jpg

Photo at left shows, the manual wire guide handle that can be moved from left to right, depending the side of the machine that works best for the customer. 

The photo to the right shows, the all steel removable chain guard. This needs to be removed from time to time to oil and service the chain. 

NOTE: Never operate the Gas Powered Wire Winder, without all guards in place at all times.

Hotwood's believes in making sure we have picked the right motor or any outside parts it takes to manufacture our products. Here, 2 men from Honda Motor Corporation, test the Honda motor we use on the Gas Powered Winder, for vibration, temperature control during operation, power output, and general performance, to be 100% positive we are using the right motor for our application. After almost 1 hour of extensive testing under load and in idling mode, The Honda specialists were very pleased, and were 100% sure we were manufacturing, not only a terrific product, but using the right components to assure the customer years of satisfaction. This is one of the reason's Hotwoods is number 1, on the market with all our wire winders we manufacture under the Pro-Tatch Inc. name, and have been for over 30 years. We want you, the customer to be happy with the performance of this unit, or any product you purchase from us. If it will not work for the customer, how is it ever going to work for us?

Hotwood's believes in making sure we have picked the right motor or any outside parts it takes to manufacture our products. Here, 2 men from Honda Motor Corporation, test the Honda motor we use on the Gas Powered Winder, for vibration, temperature control during operation, power output, and general performance, to be 100% positive we are using the right motor for our application.

After almost 1 hour of extensive testing under load and in idling mode, The Honda specialists were very pleased, and were 100% sure we were manufacturing, not only a terrific product, but using the right components to assure the customer years of satisfaction.

This is one of the reason's Hotwoods is number 1, on the market with all our wire winders we manufacture under the Pro-Tatch Inc. name, and have been for over 30 years.

We want you, the customer to be happy with the performance of this unit, or any product you purchase from us. If it will not work for the customer, how is it ever going to work for us?

Honda Gas Powered Winder

gas-winder-price.jpg

Call to order 1-877-407-8645